Mobile cellphone charger

While travelling charging of mobile battery is great problem because power supply source is not generally accessible. Here is a simple project using very common electronics components for charging mobile battery using AA cells.

Circuit descriptions of mobile cellphone charger

The main part of the circuit mobile cellphone charger is timer IC NE555, used to charge and monitor the voltage level. IC₁ get control voltage to pin 5 by zener diode ZD₁. Threshold pin 6 and trigger pin 2 is supplied with a voltage set by VR₁ and VR₂ respectively. The trigger pin 2 of IC₁ is below 1/3V_CC when discharge battery is connected to the circuit as a result flip-flop of IC₁ is switched on to take output pin 3 high. The process is reversed when battery is fully charged of charged battery is connected. Here transistor T₁ used to enhance the charging current from output pin 3 of IC₁. Adjust potentiometer VR₁ and VR₂ as per require.

LED status for different charging conditions

Load across the output	Output frequency (at pin 3)	LED₁
No battery connected	765 kHz	On
Charging battery	4.5 Hz	Blink
Fully charged battery	0	Off

PARTS LIST

Resistors (all ¼-watt, ± 5% Carbon)

R₁ = 390 Ω

R₂ = 680 Ω

R₃ = 39 Ω/1W

R₄ = 27 KΩ

R₅ = 47 KΩ

R₆ = 3.3 KΩ

R₇ = 100 Ω/1W

VR₁, VR₂ = 20 KΩ

Capacitors

C₁ = 0.001 µF (ceramic disc)

C₂ = 0.01 µF (ceramic disc)

C₃ = 4.7 µF/25V (Electrolytic )

Semiconductors

IC₁ = NE555 timer IC

T₁ = SL100

ZD₁ = 5.6 V/1W

LED₁

Miscellaneous

SW₁ = On/off switch

1.5V*8 AA cells

Mobile connector

Comments

Digital Fan Regulator Circuit Diagram

This is the project of Digital Fan Regulator Circuit diagram. The circuit presented here can be used to control the speed of fans using induction motor. The speed control is nonlinear, i.e. in steps. The current step number is displayed on a 7-segment display. Speed can be varied over a wide range because the circuit can alter the voltage applied to the fan motor from 130V to 230V RMS in a maximum of seven steps. The triac used in the final stage is fired at different angles to get different voltage outputs by applying short-dura-tion current pulses at its gate. For this pur-pose a UJT relax-ation oscillator is used that outputs sawtooth waveform. This waveform is coupled to the gate of the triac through an optocoupler (MOC3011) that has a triac driver output stage. Pedestal voltage control is used for varying the firing angle of the triac. The power supply for the relaxation oscillator is derived from the rectified mains via 10-kilo-ohm, 10W series dropping/limit-ing...

Using the SG3525 PWM Controller Explanation and Example Circuit Diagram Schematic of Push Pull Converter

PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...

FM transmitter using UPC1651

Description. Here is the circuit diagram of an FM transmitter using the IC UPC1651. UPC1651 is a wide band UHF Silicon MMIC amplifier. The IC has a broad frequency response to 1200MHz and power gain up to 19dB.The IC can be operated from 5V DC. The audio signals picked by the microphone are fed to the input pin (pin2) of the IC via capacitor C1. C1 acts as a noise filter. The modulated FM signal will be available at the output pin (pin4) of the IC. Inductor L1 and capacitor C3 forms the necessary LC circuit for creating the oscillations. Frequency of the transmitter can be varied by adjusting the capacitor C3. Circuit diagram with Parts list. Notes. The circuit can be assembled on a Vero board. Inductor L1 can be made by making 5 turns of 26SWG enameled copper wire on a 4mm diameter plastic former. A ¾ meter insulated copper wire can be used as the antenna. Do not give more than 6V to the IC. Mic M1 can be a condenser microphone.

ffd

Search This Blog