ffd

Basic Of Switch Mode Power Supply In recent years, the use of switch mode power supply (SMPS) has become more comon as more applications demand for greater power eficiency. It makes use of semiconductor (mostly MOSFET) fast switches to switch DC input that has been rectified at high frequency. The advantages of high frequency switching are that it reduces the size of inductor, capacitors & transformer used. Other advantages of switching power supply over linear power supply are : 1) High Efficiency (up to 90% and above for nice design). 2) Output can be higher than input. 3) Able to operate over a variety of input power supply. 4) Able to have over output. The setback of using SMPS compared to linear power supply is that it generates electrical noise which contributes to electromagnetic compatibility design issues & more part count. Buck Converter SMPS The SMPS circuit below from Power Integration makes use of LNK304 as its high frequency switch. Take note that this circuit is...

COMMON MODE REJECTION RATIO (CMRR) OF DIFFERENTIAL AMPLIFIER CALCULATOR Enter Differential mode gain, Ad: Enter Common mode gain, Acm: Common mode rejection ratio: Common mode rejection ratio: indB

The SMPS described here is suit-able for high-wattage stereos and other similar equipment. The circuit employs two high-voltage power transistors (BU208D) which have built-in re-verse-connected di-odes across their collectors and emitters. It can supply about 250-watt out-put. The circuit uses a ferrite core transformer of 14mm width, 20mm height, and 42mm length of E-E cores. An air gap of 0.5 mm is required between E-E junction. Good insulation using plastic-insulating sheets (Mylar) is to be maintained between each layer of winding. Circuit diagram: Simple Switch Mode Power Supply Circuit Diagram The number of primary turns required is 90 with 26 SWG wire. The secondary winding employs 17 SWG wire (for 4A load current). Each turn of the secondary develops approximately 2 volts. The reader can decide about the output volt-age and the corresponding secondary turns, which would work out to be half the desired secondary voltage. The volt-age rating of capacitors C7 and C8 should be at...

Used ICs: MSP3410G, 24C16, SDA55xx, VSP9402, DDP3315C, TDA4470M, STR-F6654, TDA8358J, TDA6108JF - Panasonic TX-29E50D, TX-29E50D/B, TX-29PS12D, TX-29PS12F, TX-29PS12P  ALIGNMENT SETTINGS (The figures below are nominal and used for representative purposes only.) To access Service Mode select program position 99 and set sharpness to minimum. Press “MUTE” button on remote control and at the same time press the „ ∨ ” button on the customer controls at the front of the TV, this will place the TV set into Service Mode. Press ∧ / ∨ buttons to step up / down through the functions. Press + / - buttons to alter the function values. To exit Service Mode press „MENU” button. TX-29E50D, TX-29E50D/B, TX-29PS12D, TX-29PS12F, TX-29PS12P - MAIN-BOARD PTMPMSV29P1FF circuit diagram

Switching Power supply circuit produces a voltage B + (dc voltage) needed television series taken from the net voltage household. G7 G7A chassis and power supply circuit using cool / cold in which the primary and the secondary power supply electrically separated so that the chassis can be directly connected to another device via an audio video terminal. Switching power supply This power supply circuit is a type SMPS (Switching Mode Power Supply) using mosfet transistor integrated circuit voltage controller in one IC package, namely STR-W6654. This IC will control the duty cycle of time off Vth2 Mosfet transistor to control the output voltage. Besides, the IC is also equipped with a safety circuit against overvoltage (OVP), overcurrent (OCP) and over temperature (TSD) circuit is working on 220V ac voltage with the input ac voltage range of 176V to 260V ac or known by the Wide range Regulators. How to Work Series Initial bias voltage dc pin6 IC801 obtained from an ac voltage through D811...

In many projects use is made of alphanumeric LCDs that are driven internally by Hitachi’s industry-standard HD44780 controller. These displays can be driven either in 4-bit or 8-bit mode. In the first case only the high nibble (D4 to D7) of the display’s data bus is used. The four unused connections still deserve some closer attention. The data lines can be used as either inputs or outputs for the display. It is well known that an unloaded output is fine, but that a floating high-impedance input can cause problems. So what should you do with the four unused data lines when the display is used in 4-bit mode? This question arose when a circuit was submitted to us where D0-D3 where tied directly to GND (the same applies if it was to +5 V) to stop the problem of floating inputs. The LCD module was driven directly by a microcontroller, which was on a development board for testing various programs and I/O functions. There was a switch present for turning off the enable of the display when it wa...