Skip to main content

Posts

Showing posts with the label Wave

600W 50Hz sine wave inverter test circuit

Here I tested a 600W 50Hz sine wave inverter circuit using push-pull topology instead of full-bridge topology. 2 PIC16F684's were used - one for SPWM and one for charging. 2 microcontrollers were used intentionally as the purpose was to test if I could use the microcontrollers together and use each of them for multitasking. 2 auxiliary transformers are used - one for powering the circuitry when running off mains and one for current sensing. Charging is done with 4 relays that are turned on/off according to input voltage and accordingly connect the input voltage to an appropriate transformer winding/tapping to keep output voltage relatively constant. Switching frequency is 16kHz. The sine table has 32 values. Here is the complete sine table: 0, 16, 32, 47, 62, 77, 91, 103, 115, 126, 136, 144, 151, 156, 160, 162, 163, 162, 160, 156, 151, 144, 136, 126, 115, 103, 91, 77, 62, 47, 32, 16, //65% 0, 17, 33, 49, 65, 80, 94, 107, 120, 131, 141, 149, 156, 162, 166, 168, 169, 168, 166, 162, 1...

Triangular Wave Oscillator Circuit Diagram

Triangular Wave Oscillator Circuit Diagram . This design resulted from the need for a partial replacement of the well-known 8038 chip,  which is no longer in production and there fore hardly obtainable.  An existing design for driving an LVDT sensor (Linear Variable Differential Transformer),  where the 8038 was used as a variable sine  wave oscillator, had to be modernised. It may  have been possible to replace the 8038 with an  Exar 2206, except that this chip couldn’t be used  with the supply voltage used. For this reason we  looked for a replacement using standard components, which should always be available. In this circuit two opamps from a TL074 (IC1.A  and B) are used to generate a triangular wave,  which can be set to a wide range of frequencies using P1. The following differential amplifier using T1 and T2 is configured in such a way  that the triangular waveform is converted into  a reasonably looking sinusoidal wavefo...

Short Wave Converter

This short-wave converter, which doesn’t have a single coil requiring alignment, is intended to enable simple medium-wave receivers to be used to listen to short-wave signals. The converter transforms the 49-m short-wave band to the medium-wave frequency of 1.6 MHz. At the upper end of the medium-wave band, select an unoccupied frequency that you want to use for listening to the converted short-wave signals. Good reception performance can be obtained using a wire antenna with a length of one to two metres. Short-Wave Converter  Circuit Diagram The converter contains a free-running oscillator with a frequency of around 4.4 MHz, which is tuned using two LEDs (which act as variable-capacitance diodes!) and a normal potentiometer. The frequency range is set by adjusting the emitter current using a 1k trimpot. The oscillator frequency depends strongly on the operating point. This is due to the combination of using an audio transistor and the extremely low supply voltage. Under these con...

2MHz Square Wave Generator Circuit Diagram

2MHz Square Wave Generator Circuit Diagram. With the values shown the circuit generates a 2-MHz symmetrical square wave. Changing capacitors Cl and C2 to 0.01 µ¥ results in a frequency of 500 Hz. For the particular integrated circuits and power supply voltages (5.0 V), the reliable operating range of Rl = R2 is 2 k ohm to 4 k ohm. 2MHz Square Wave Generator Circuit Diagram

Wave antenna 5 8 pro VKV FM

Wave antenna 5/8 consists of a vertical radiator which is fed at the base of the antenna. A suitable device of some sort should be added between the antenna and feedline if you want to eat with coax. Adding a coil in series with the antenna on the base is one of these methods are suitable.  So why would anyone use an antenna 5/8 wave if they have to go through all that extra work? After all, a ground plane antenna provides a good match. There are several answers. The first is GAIN. The computer shows that the antenna (mounted 1 foot above the ground) has a margin of about 1.5 dBd higher than a dipole (also installed 1 foot above the ground.)The second reason you might want to use the wave 5/8 vertical is to get a lower angle of radiation. Peak radiation angle A half-wave antenna is 20 degrees. You will find that the angle 5/8 wave antenna radiation is only 16 degrees so it is better dx antenna.   You may have noticed a pattern developing here. A quarter-wave ground plane ...

Short Wave Superregenerative Receiver

Superregenerative receivers are characterised by their high sensitivity. The purpose of this experiment is to deter-mine whether they are also suitable for short-wave radio. Superregenerative receivers are relatively easy to build. You start by building a RF oscillator for the desired frequency. The only difference between a superregenerative receiver and an oscillator is in the base circuit. Instead of using a voltage divider, here we use a single, relatively high-resistance base resistor (100 kΩ to 1MΩ). Superregenerative oscillation occurs when the amplitude of the oscillation is sufficient to cause a strong negative charge to be applied repeatedly to the base. If the regeneration frequency is audible, adjust the values of the resistors and capacitors until it lies somewhere above 20 kHz. The optimum setting is when you hear a strong hissing sound. The subsequent audio amplifier should have a low upper cutoff frequency to strongly attenuate the regeneration signal at its output whi...

Generation of AM wave

Introduction  Purpose of a communication system: convey information through a medium or communication channel. ◊    The information is often represented as a baseband signal, i.e. a signal whose spectrum extends           from 0 to some maximum frequency. ◊     Proper utilization of the communication channel often requires a shift of the range of baseband         frequencies into other frequency ranges suitable for transmission, and a corresponding shift back to     the original frequency range after reception. ◊    A shift of the range of frequencies in a signal is accomplished by using modulation, which is             defined as the process by which some characteristic of a carrier is varied in accordance with                 modulating (signal) ◊      A common form of the carrier is a sinusoidal wave, in which c...