ffd

Description This is the most simple fm receiver with good performances that works great even if the sensitivity is not too high. The working principle of this fm receiver may seem a little unusual. It is made of an oscillator (T2 and T3) that is synchronized with the received frequency of T1. This transistor works as a broadband preamplifier in VHF range.  The oscillator is adjusted between 87 … 108 MHz with C5. Because of the synchronization, the oscillator output will have the same frequency deviation as the received signal from the fm antenna. This deviations are caused by the broadcasted audio informations. The frequency modulated signal show up on P1 + R5. Low pass filter R6/C6 extracts the audio signal and then is amplifier by T4 … T6 and transmitted at the output through C9 capacitor. Circuit Diagram The coil details are presented in the fm receiver circuit diagram. The radio receiver is adjusted on different stations with the help of C5. P1 potentiometer is adjusted untill ...

This is a simple design, can have excellent results, he is a recipient of regeneration, if you have never built any receiver, this is one you will build Easy. The circuit described is simple and has many limitations in sensitivity and selectivity, but is able to receive signals from radio amateurs (40m or 80m) in SSB and CW, and as output using a small headset crystal.  He will have a saturation if there are strong stations available on AM broadcast band of 41m at night.L1 is a small toroid T50-2 (red) with about 18 to 20 times (40m) or 35 to 40 times (80m) in the main winding connected to the FET with a single coupling circuit facing the antenna connection.  The center tap is about 20% of the primary winding. C1 is adjusted to set the radio band to the 40m and C2 then acts as a fine tuning within the band.The supply of 12 to 14V, R2 should be increased 5K6 or 6K8 output will be higher and similar sensitivity to-100dBm (about 2uV). Regenerative Receiver Circuit Diagram

Transmitter and receiver circuit using infra red audio signal is applied to emit an audio signal and will received on a headphones. Making his series is not too difficult, the transmitter and receiver circuit scheme can be seen below. Transmiter schematics Receiver schematics After the series finished, you can try to give the audio inputs on the transmitter and point the LED transmitter to the receiver. Maximum distance is a few meters may not be more than 10 meters, but you can listen to music without wires while using infra red. image[link]

Just as in the transmitter circuit, the series of FM Wireless Microphone Receiver Hi Fi also uses an FM audio receiver module. Module used in the circuit FM Wireless Microphone Receiver Hi Fi has a good feture, namely audio FM receiver module has a function that is able to muffle the noise squel. Audio FM receiver module that is used in FM Wireless Microphone Receiver Hi Fi also does not require a lot of supporting components in the RF signal reception. Audio FM receiver module only requires a 5 volt DC voltage source and a potentiometer P2 to set the threshold level of noise that will be muffled. Voltage source to an audio FM receiver module is also to go through the regulator is good, because if the quality of resources kuran it will generate noise. At the output line installed capacitors C3 and C4 as a couple and compensator for output in accordance with the amplifier or mixer (100mV rms). Part Series FM Wireless Microphone Receiver Hi Fi To provide an output signal according to the...

Superregenerative receivers are characterised by their high sensitivity. The purpose of this experiment is to deter-mine whether they are also suitable for short-wave radio. Superregenerative receivers are relatively easy to build. You start by building a RF oscillator for the desired frequency. The only difference between a superregenerative receiver and an oscillator is in the base circuit. Instead of using a voltage divider, here we use a single, relatively high-resistance base resistor (100 kΩ to 1MΩ). Superregenerative oscillation occurs when the amplitude of the oscillation is sufficient to cause a strong negative charge to be applied repeatedly to the base. If the regeneration frequency is audible, adjust the values of the resistors and capacitors until it lies somewhere above 20 kHz. The optimum setting is when you hear a strong hissing sound. The subsequent audio amplifier should have a low upper cutoff frequency to strongly attenuate the regeneration signal at its output whi...

Description: The following circuit shows about Noisy Regen Receiver Circuit Diagram. Features: Noisy Regenerative Receiver Circuit, making it easier to integrate with common-grounded test equipment, used PNP transistors (2N3906). Component: Inductor, Transistor, Battery, Capacitor, Antenna, Resistor.

The project is a user-friendly and cheap FM radio receiver which produces the desired audio signals using integrated circuit to achieve the pre-processing units. During operation, the user is allowed to change stations and interact with the receiver by integrating a keypad and an LCD for communication. There are several functions that this radio receiver can perform including adjusting the threshold when picking up stronger or weaker stations, setting up 3 favorite stations for quick tuning, scanning up/down for next strong signal station, and tuning up/down a frequency. A keypad is designed for controlling the receiver and the buttons are mapped to their corresponding functionality while the other buttons are not connected. The 4 main sub-components of the receiver include the LCD, the keypad, the favorite station storage, and the communication with receiver. Each of them is being controlled by their software components. The antenna transfers the incoming radio signal to the AR1010 F...

Description: This is a compact three transistor, regenerative receiver with fixed feedback. It is similar in principle to the ZN414 radio IC which is now no longer available. The design is simple and sensitivity and selectivity of the receiver are good. Circuit diagram Notes: All general purpose transistors should work in this circuit, I used three BC109C transistors in my prototype.The tuned circuit is designed for medium wave. I used a ferrite rod and tuning capacitor from an old radio which tuned from approximately 550 - 1600kHz. Q1 and Q2 form a compund transistor pair featuring high gain and very high input impedance. This is necessary so as not to unduly load the tank circuit. The 120k resistor provides regenerative feedback,between Q2 output and the tank circuit input and its value affects the overall performance of the whole circuit. Too much feedback and the circuit will become unstable producing a "howling sound". Insufficient feedback and the receiver becomes ...

Remote sensor sends data via mains supply, Temperature range: 00.0 to 99.9 °C This circuit is intended for precision centigrade temperature measurement, with a transmitter section converting to frequency the sensor's output voltage, which is proportional to the measured temperature. The output frequency bursts are conveyed into the mains supply cables. The receiver section counts the bursts coming from mains supply and shows the counting on three 7-segment LED displays. The least significant digit displays tenths of degree and then a 00.0 to 99.9 °C range is obtained. Transmitter-receiver distance can reach hundred meters, provided both units are connected to the mains supply within the control of the same light-meter. Transmitter circuit operation: IC1 is a precision centigrade temperature sensor with a linear output of 10mV/°C driving IC2, a voltage-frequency converter. At its output pin (3), an input of 10mV is converted to 100Hz frequency pulses. Thus, for example, a temperatur...

I use my computer every single minute, I do my work at home and I need to finish lots of paperwork. My computer helps me in almost everything I do. I make sure that my pc is able to do multitasking and functioning well. Just like our body, it should be fit to do all the workload that must be finished within the day. To come up with another task that a pc can add to its functions, an IR remote was created through an FTDI that receives and transmits data other than the Universal Serial Bus. This is definitely a big help that my pc can easily cope up with simultaneously.