ffd

The author is the happy owner of a television set with built-in Ambilight lighting in the living room. Unfortunately, the television set in  the bedroom lacks this feature. To make up for this, the author attached a small lamp to the wall to provide background lighting, This makes  watching television a good deal more enjoyable, but it ’s  not the ideal solution. Although the TV set can be  switched off with the remote  control, you still have to get out of bed to switch off the lamp. Circuit diagram : Automatic TV Lighting Switch Circuit Diagram Consequently, the author devised this automatic lighting switch that switches the background light on and off along with the T V set. The entire circuit is fitted in series with the mains cable of the TV set, so there’s no need to tinker with the set. It works as follows: R1 senses  the current drawn by the TV  set. It has a maximum value  of 50 mA in standby mode,  rising  to around ...

Used ICs:  24C08 – TMPA8829 – 4052 – MSP34X5G – TDA8944 – TDA8945 – TC90A49P – TDA8177 – TDA16846 – BCK4901-XX(LOT) CTV CIRCUIT

The TV remote control transmits television signals as pulses of frequency around 37.5kHz. Each button on the remote control is pressed or equivalent has a pulse signal codes. This remote transmits pulses of the circuit block of the same frequency as the remote to your TV confuse decoding the transmitted signal. The heart of the circuit is the 555 timer IC in astable circuit works mode.The output series of pulses at a frequency of 18 kHz to 48 kHz by simply adjusting the 5K potentiometer. What you do is adjust the potentiometer until frequeny jives to its distance from the TV or until the signal is ignored by television.  TV Remote Jammer Using 555 IC Circuit Diagram Read more IC Circuits

The author is the happy owner of a television set with built-in Ambilight lighting in the living room. Unfortunately, the television set in  the bedroom lacks this feature. To make up for this, the author attached a small lamp to the wall to provide background lighting, This makes  watching television a good deal more enjoyable, but it ’s  not the ideal solution. Although the TV set can be  switched off with the remote  control, you still have to get out of bed to switch off the lamp.   Circuit diagram :   Automatic TV Lighting Switch Circuit Diagram   Consequently, the author devised this automatic lighting switch that switches the background light on and off along with the T V set. The entire circuit is fitted in series with the mains cable of the TV set, so there’s no need to tinker with the set. It works as follows: R1 senses  the current drawn by the TV  set. It has a maximum value  of 50 mA in standby mode,  rising  to around   500 m A  when  the  set  is  operating. The ...

LG Cinema Screen 47LM7600 47-Inch Cinema 3D 1080p 240 Hz LED-LCD HDTV with Smart TV and Six Pairs of 3D Glasses. Features and Technical Details : Size: 47-Inch Product Features LG LED Plus backlighting delivers superior brightness, clarity and color detail from the edges of the screen, resulting in an amazingly thin, energy efficient LED TV with local dimming for a higher contrast ratio and deeper blacks. With LG Cinema 3D technology you can enjoy amazing 3D effects, comfortable lightweight battery free glasses, 2D to 3D content conversion, 3D depth control and a clear picture from virtually any angle. See sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LG's TruMotion 240Hz technology. Now your TV can keep up with the fastest moving scenes. LG's Smart TV is a revolutionary, easy way to access limitless content, thousands of movies, customizable apps, videos and browse the web all set up in a simple to use interface. The Magic ...

Used ICs: LA7263 – LA76931 – 24C08 -  LA78040 – BSC28-070(LOT) – TDA16846(SMPS CONTROL) – TC4052 – LV1116

This circuit is able to identify PAL and NTSC video signals. Its output is high for an NTSC signal and low if the signal is PAL. This output signal can be used, for example, to automatically switch in a colour subcarrier converter or some other device while an NTSC signal is being received. One application is for the reception from satellites of 'free-to-air' TV signals, which in Australia generally contain a mixture of 625-line PAL and 525-line NTSC programs. Operation of the circuit is as follows. IC1 is an LM1881 video sync separator which takes the video input signal and generates vertical synchronisation pulses. For an NTSC signal, these pulses are 16.66ms apart, corresponding to the 60Hz field rate, while for a PAL signal they are 20ms apart, corresponding to the 50Hz field rate. The vertical sync pulses are fed into IC2a, the first of two dual retriggerable monostable multivibrators in the 74HC123A. IC2a has a period of very close to 17.9ms, set by the 200kO resistor and...

This is my first post and and this is the first circuit i made. There are many types of circuits for controlling home appliances using TV Remote. In fact I had confused a lot when I am a beginner searching for this type of circuits. The circuit here 555 timer IC to avoid fast switching. you can only switch the circuit after 3 seconds. IR remote sensor IC TSOP 1738 is used for recieving the signal. Normally when no signal is falling on IC3 the output of it will be high.This makes Q1 OFF.When a signal of 38 KHz from the TV remote falls on the IC3 its output goes low.This makes Q1 conduct and a negative pulse is obtained at pin 2 of IC 1 NE 555.Due to this IC1 wired as a monostable multivibrator produces a 4 Sec long high signal at its out put. This high out put is the clock for IC 2 which is wired as a Flipflop and of , its two outputs pin 3 goes low and pin 2 goes high.The high output at pin 2 is amplified to drive the relay .For the next signal the outputs of IC2 toggles state. Result...

The schematic above can be used for supply on color TV for all type TV circuit. But we need to know how much voltage needed by the circuit of color Television. To set the output voltage, the setting on VR1 1K ohm. Required input voltage 300V DC which is already on TV circuit, so we just take a 300V dc voltage existing on the TV circuit, and for a circuit supply voltage on our TV cut the line PCB and connected with this  universal switching power supply.For the transformer we can use the TV regulator transformer. Part List : R1 = 33R 5W R2 = 330R 1W R3 = 2K2 R4 = 47K R5 = 2K7 R6 = 22K R7 = 390K R8 = 47R 1W C1 = 100uF 25V C2 = 1n2 2KV C3 = 18n C4 = 18n D1 = 1N4148 D2 = 1N4148 D3 = ZD 12V D4 = 1N4007 D5 = 1N4007 VR1 = 1K ZD1 = Zener 6V T1    = TV regulator transformer Q1   = K2847 Q2   = C2328A PCB line Finishes circuit

Used ICs: MSP3410G, 24C16, SDA55xx, VSP9402, DDP3315C, TDA4470M, STR-F6654, TDA8358J, TDA6108JF - Panasonic TX-29E50D, TX-29E50D/B, TX-29PS12D, TX-29PS12F, TX-29PS12P  ALIGNMENT SETTINGS (The figures below are nominal and used for representative purposes only.) To access Service Mode select program position 99 and set sharpness to minimum. Press “MUTE” button on remote control and at the same time press the „ ∨ ” button on the customer controls at the front of the TV, this will place the TV set into Service Mode. Press ∧ / ∨ buttons to step up / down through the functions. Press + / - buttons to alter the function values. To exit Service Mode press „MENU” button. TX-29E50D, TX-29E50D/B, TX-29PS12D, TX-29PS12F, TX-29PS12P - MAIN-BOARD PTMPMSV29P1FF circuit diagram

Haier 32 inch LCD TV - LE32H86 - Power supply regulator and T'Con, and Audio output board circuit diagram.  Used ICs: MSH9010, SSC9502S, STR-A6059HMST6M181S  Service mode Menu > 8 > 8 > 9 > 3 > Enter. SMPS schematic T'Con board Audio output Click on the schematics to magnify

This circuit was designed to assist the installation of TV antennas. The signal is monitored using a small portable TV set and this circuit monitors the output of the TV's FM detector IC via a shielded lead. To initially calibrate the meter, adjust trimpot VR2 to zero the meter. Trimpot VR1 is a sensitivity control and can be set for a preset reading (ie, 0dB) or can be calibrated in millivolts. Rotating the antenna for a minimum reading on the meter (indicating FM quieting) gives the optimum orientation for the antenna. Circuit diagram: TV Relative Signal Strength Meter Circuit Diagram

This circuit was designed to assist the installation of TV antennas. The signal is monitored using a small portable TV set and this circuit monitors the output of the TV's FM detector IC via a shielded lead. To initially calibrate the meter, adjust trimpot VR2 to zero the meter. Trimpot VR1 is a sensitivity control and can be set for a preset reading (ie, 0dB) or can be calibrated in millivolts. Rotating the antenna for a minimum reading on the meter (indicating FM quieting) gives the optimum orientation for the antenna. TV Relative Signal Strength Meter Circuit diagram: TV Relative Signal Strength Meter Circuit Diagram

Power Supply Circuit Diagram - Philco 32" LED LCD TV