Skip to main content

Electricity and the Electron


What is electricity?

Lamp switching on and offElectricity is the flow of charge around a circuit carrying energy from the battery (or power supply) to components such as lamps and motors.
Electricity can flow only if there is a complete circuit from the battery through wires to components and back to the battery again.
The diagram shows a simple circuit of a battery, wires, a switch and a lamp. The switch works by breaking the circuit.
With the switch open the circuit is broken - so electricity cannot flow and the lamp is off.
With the switch closed the circuit is complete - allowing electricity to flow and the lamp is on. The electricity is carrying energy from the battery to the lamp.
We can see, hear or feel the effects of electricity flowing such as a lamp lighting, a bell ringing, or a motor turning - but we cannot see the electricity itself, so which way is it flowing? 

Conventional current
Imaginary positive particles
moving in the direction of
the conventional current

Which way does electricity flow?

We say that electricity flows from the positive (+) terminal of a battery to the negative (-) terminal of the battery. We can imagine particles with positive electric charge flowing in this direction around the circuit, like the red dots in the diagram.
This flow of electric charge is called conventional current.
This direction of flow is used throughout electronics and it is the one you should remember and use to understand the operation of circuits.
However this is not the whole answer because the particles that move in fact have negative charge! And they flow in the opposite direction! Please read on... 

Electrons flowing

The electron

When electricity was discovered scientists tried many experiments to find out which way the electricity was flowing around circuits, but in those early days they found it was impossible to find the direction of flow.
They knew there were two types of electric charge, positive (+) and negative (-), and they decided to say that electricity was a flow of positive charge from + to -. They knew this was a guess, but a decision had to be made! Everything known at that time could also be explained if electricity was negative charge flowing the other way, from - to +.
The electron was discovered in 1897 and it was found to have a negative charge. The guess made in the early days of electricity was wrong! Electricity in almost all conductors is really the flow of electrons (negative charge) from - to +.
By the time the electron was discovered the idea of electricity flowing from + to - (conventional current) was firmly established. Luckily it is not a problem to think of electricity in this way because positive charge flowing forwards is equivalent to negative charge flowing backwards.
To prevent confusion you should always use conventional current when trying to understand how circuits work, imagine positively charged particles flowing from + to -. 


Comments

Popular posts from this blog

Digital Fan Regulator Circuit Diagram

This is the project of Digital Fan Regulator Circuit diagram. The circuit presented here can be used to control the speed of  fans using induction motor. The speed control is nonlinear, i.e. in steps. The current step number is displayed on a 7-segment display. Speed can be varied over a wide range because the circuit can alter the voltage applied to the fan motor from 130V to 230V RMS in a maximum of seven steps.  The triac used in the final stage is fired at different angles to get different voltage outputs by applying short-dura-tion current pulses at its gate. For this pur-pose a UJT relax-ation oscillator is used that outputs sawtooth waveform. This waveform is coupled to the gate of the triac through an optocoupler (MOC3011) that has a triac driver output stage.  Pedestal voltage control is used for varying the firing angle of the triac. The power supply for the relaxation oscillator is derived from the rectified mains via 10-kilo-ohm, 10W series dropping/limit-ing...

Using the SG3525 PWM Controller Explanation and Example Circuit Diagram Schematic of Push Pull Converter

PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...

Automatic Intruder Alarm Circuit Diagram

Description: This is a simple single-zone burglar alarm circuit. Its features include automatic Exit and Entry delays and a timed Bell/Siren Cut-Off. It's designed to be used with the usual types of normally-closed input devices such as - magnetic reed contacts - micro switches - foil tape - and PIRs. But it can be Easily Modified to accept normally-open triggering devices - such as pressure mats. Circuit Diagram   Notes:   It's easy to use. First check that the building is secure and that the green LED is lit. Then move SW1 to the "set" position. The red LED will light. You now have about 30 seconds to leave the building. When you return and open the door - the Buzzer will sound. You then have about 30 seconds to move SW1 to the "off" position. If you fail to do so - the relay will energize and the Siren will sound. While at least one of the switches in the normally-closed loop remains open - the Siren will continue to sound. However, about 15-minutes aft...