TDA7375 Audio Amplifier 2x35W

TDA7375 general description:

Circuit of quadruple audio amplifier using integrated circuit TDA7235 for systems surround. Circuit of quadruple amplifier for systems surround using the ci tda7375, for potency of 7 watts for channel in the version amplifying quad or 15 watts in the dual version (stereo). could arrive to 35 watts in the version.TDA7235 is a circuit integrated amplifier quadruple audio amplifier class AB capable to work in double bridge or simple quadruple amplifiers, circuit integrated with protection system of short, it requests the minimum of external components, available in multiwat 15H (TDA7375H) and multiwat 15V (TDA7375V). Although the first conception went to automotives pplications , to give him/it in a great variety of applications of low potency. That integrated circuit is ideal in the situation in that is wanted a reasonable potency and with a Power tension relatively low for your operation. That circuit drawn below it uses the basic configuration of quadruple amplifier, but using a configuration in bridge, it can be obtained about 4 times the maximum potency. In that configuration of quadruple amplifier it can be used as amplifier end of systems surround, when 7 watts for channel are already a good potency, using the minimum of components.Operation of the circuit of the audio amplifier with tda7375 The capacitor C8 uncouples the internal tension divisor. The capacitors C5 and C6 are the filter for Power supply. The capacitors of 2200µF / 25V are the exit capacitors. Vs is the Power supply that can be a car battery or a supply of 14 volts. Power supply for the circuit It can be with a transformer 12V/30VA, a rectifier bridge and a capacitor electrolytic of 4700µF or (larger). The maximum consumption of current with loads of 4Ohms is 2.1 A. You can use loads of 2 ohms, but he/she also remembers to increase the size of the of heat-sink, because the circuit integrated in Multiwat package it will heat up a little more. Suggestion of printed circuit board side of the copperSuggested PCB for mounting the amplifier tda7375, component side Information about mounting circuit audio amplifier. When assembling the circuit remember that this quad amplifier channels features two four inverted, then it should connect the speakers in reverse polarity at such times, attention to the polarity of electrolytic capacitors that should be of good quality. Before welding the tda7375 remember to solder the jumper, which will be underneath the integrated. TDA7375 Audio Amplifier 2x35W

TDA7375 features:

HIGH OUTPUT POWER CAPABILITY:

– 2 x 40W max./4
– 2 x 35W/4 EIAJ
– 2 x 35W/4 EIAJ
– 2 x 25W/4 @14.4V, 1KHz, 10%
– 4 x 7W/4 @14.4V,1KHz, 10%
– 4 x 12W/2 @14.4V, 1KHz, 10%

MINIMUM EXTERNAL COMPONENTS

COUNT:
– NO BOOTSTRAP CAPACITORS
– NO BOUCHEROT CELLS
– INTERNALLY FIXED GAIN (26dB BTL)

ST-BY FUNCTION (CMOS COMPATIBLE)
NO AUDIBLE POP DURING ST-BY OPERATIONS

DIAGNOSTICS FACILITY FOR:

– CLIPPING
– OUT TO GND SHORT
– OUT TO VS SHORT
– SOFT SHORT AT TURN-ON
– THERMAL SHUTDOWN PROXIMITY

TDA7375 circuit diagram:

Double Bridge TDA7375

Quad SterioTDA7375

SterioBridge TDA7375

TDA7375 layout:

pcb layout

Digital Fan Regulator Circuit Diagram

This is the project of Digital Fan Regulator Circuit diagram. The circuit presented here can be used to control the speed of fans using induction motor. The speed control is nonlinear, i.e. in steps. The current step number is displayed on a 7-segment display. Speed can be varied over a wide range because the circuit can alter the voltage applied to the fan motor from 130V to 230V RMS in a maximum of seven steps. The triac used in the final stage is fired at different angles to get different voltage outputs by applying short-dura-tion current pulses at its gate. For this pur-pose a UJT relax-ation oscillator is used that outputs sawtooth waveform. This waveform is coupled to the gate of the triac through an optocoupler (MOC3011) that has a triac driver output stage. Pedestal voltage control is used for varying the firing angle of the triac. The power supply for the relaxation oscillator is derived from the rectified mains via 10-kilo-ohm, 10W series dropping/limit-ing...

Using the SG3525 PWM Controller Explanation and Example Circuit Diagram Schematic of Push Pull Converter

PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...

Automatic Intruder Alarm Circuit Diagram

Description: This is a simple single-zone burglar alarm circuit. Its features include automatic Exit and Entry delays and a timed Bell/Siren Cut-Off. It's designed to be used with the usual types of normally-closed input devices such as - magnetic reed contacts - micro switches - foil tape - and PIRs. But it can be Easily Modified to accept normally-open triggering devices - such as pressure mats. Circuit Diagram Notes: It's easy to use. First check that the building is secure and that the green LED is lit. Then move SW1 to the "set" position. The red LED will light. You now have about 30 seconds to leave the building. When you return and open the door - the Buzzer will sound. You then have about 30 seconds to move SW1 to the "off" position. If you fail to do so - the relay will energize and the Siren will sound. While at least one of the switches in the normally-closed loop remains open - the Siren will continue to sound. However, about 15-minutes aft...

ffd

Search This Blog