Fan on off Control by Light Circuit Diagram

This circuit lets you turn on/off a fan by just directing torchlight or other light toward its light-dependent resistor (LDR). The circuit is powered from a 5V power supply.

Preset VR1 and a light-dependent resistor (LDR) work as the potential divider. Normally, the LDR’s resistance is high (20 kilo-ohms) in darkness and low (2 kilo-ohms) in light. This value of high and low resistances varies for other LDRs. Preset VR1 is used for setting the intensity of light, while preset VR2 is used for setting the output time period of IC1.

Fan on/off Control by Light Circuit Diagram

When light falls on the LDR, the monostable (IC1) triggers at pin 2, making its output at pin 3 from low to high. This low-to-high transition forms a clock for D flip-flop. The D flip-flop is operated in toggle mode by connecting its Q output to D point. The flip-flop output goes to an inverter (N1). The inverter output is fed to the relay driver transistor.

When the inverter output is low, diode D1 conducts and the current is diverted into the inverter. Hence the relay does not energise. When the inverter output is high, diode D2 conducts and the current is diverted into transistor T. Hence the relay energises.

One terminal of the fan is connected to the normally-open (N/O) contact of the relay, while another terminal is connected to the neutral (N) of mains. The mains live (L) is connected to the pole of the relay. When the relay energises, the fan turns on. Otherwise, the fan remains off.

Switches S1 and S3 are for initial resetting of the monostable (IC1) and D flip-flop (IC2), respectively, and switch S2 is used for setting the D flip-flop. Paste a piece of paper on the face of the LDR so that it doesn’t get activated by ambient light. Use a torch to light the LDR.

After initial resetting of the monostable and D flip-flop, the inverter output goes high and the fan turns on via the relay. When light falls on the LDR, the fan goes off. If torchlight is again directed toward the LDR, the fan turns on. The sequence repeats.

Initially if switch S2 is used to set the D flip-flop, the fan is held ‘off’. The relay does not energise as the Q output of D flip-flop goes high to make the inverter output low. Directing the light towards the LDR at this moment turns the fan ‘on.’

Sourced By: EFY Author: V. Gopalakrishnan

Comments

Digital Fan Regulator Circuit Diagram

This is the project of Digital Fan Regulator Circuit diagram. The circuit presented here can be used to control the speed of fans using induction motor. The speed control is nonlinear, i.e. in steps. The current step number is displayed on a 7-segment display. Speed can be varied over a wide range because the circuit can alter the voltage applied to the fan motor from 130V to 230V RMS in a maximum of seven steps. The triac used in the final stage is fired at different angles to get different voltage outputs by applying short-dura-tion current pulses at its gate. For this pur-pose a UJT relax-ation oscillator is used that outputs sawtooth waveform. This waveform is coupled to the gate of the triac through an optocoupler (MOC3011) that has a triac driver output stage. Pedestal voltage control is used for varying the firing angle of the triac. The power supply for the relaxation oscillator is derived from the rectified mains via 10-kilo-ohm, 10W series dropping/limit-ing...

Using the SG3525 PWM Controller Explanation and Example Circuit Diagram Schematic of Push Pull Converter

PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...

Automatic Intruder Alarm Circuit Diagram

Description: This is a simple single-zone burglar alarm circuit. Its features include automatic Exit and Entry delays and a timed Bell/Siren Cut-Off. It's designed to be used with the usual types of normally-closed input devices such as - magnetic reed contacts - micro switches - foil tape - and PIRs. But it can be Easily Modified to accept normally-open triggering devices - such as pressure mats. Circuit Diagram Notes: It's easy to use. First check that the building is secure and that the green LED is lit. Then move SW1 to the "set" position. The red LED will light. You now have about 30 seconds to leave the building. When you return and open the door - the Buzzer will sound. You then have about 30 seconds to move SW1 to the "off" position. If you fail to do so - the relay will energize and the Siren will sound. While at least one of the switches in the normally-closed loop remains open - the Siren will continue to sound. However, about 15-minutes aft...

ffd

Search This Blog